• Call One Of Our Experts Today: 313-563-1058

  • #1 Innovators In Minibike And Go Kart Performance!

Navigate to the www.studzracing.com homepage

Most Orders Shipped Same Day
Only in the U.S.

Home >
6270 ARC Rod, Honda GX200 STD OHV 3.303

6270 ARC Rod, Honda GX200 STD OHV 3.303

3 Reviews
$
$76.99
Savings: $
Product Code: 6270

ARC stock length billet rod with bearing inserts for the GX200 & GX160 or the BSP196cc(Clone)

3.303" center-to-center for a 1.180 rod journal and .709" wrist pin. For use with the stock crankshaft and stock style (dished or flat top) piston in modified engines. Uses ARC's custom manufactured bearing inserts and ARP rod bolts manufactured specifically for ARC. ARC has the only forced oiling scoop dipper rods available for these engines providing superior lubrication at the bearing journal.

For use with the stock crankshaft and stock style (dished or flat top) piston in modified engines. Uses ARC's custom manufactured bearing inserts and ARP rod bolts manufactured specifically for ARC. ARC has the only forced oiling scoop dipper rods available for these engines providing superior lubrication at the bearing journal.

Rod bolt torque: 170 in/lbs lubricated

Also available in longer lengths to bring the piston up closer to the top of the deck without machining the block. +.010 (#6269) and +.020 (#6271) Also stock replacement for the Kohler CH270.

Installation Instructions:

To install your ARC rod you will need a 12 point 1/4" socket and a QUALITY inch pound torque wrench. You will need an outside micrometer, dial bore gauge or plasti gauge, and oil.

Measure the crank pin diameter with the outside mic, it should measure 1.180" +/-.0005". Measure in several spots to insure roundness. If out of round more than .0005" it probably should be replaced. The crank pin finish should be smooth to the touch.

When disassembling the rod notice on the side of the rod with the part number there are two dots next to the separation point of the beam and cap. These dots help to re-orientate the cap and beam when assembled. The side of the rod with the part number engraved will always face the side cover side.

Make sure the bearing and rod serrations are clean and install the bearings. Lubricate the rod bolt threads and hand tighten the bolts. Using the torque wrench tighten the bolts to 60" lbs. Alternate each side to increase the torque by 20" lbs at a time until you reach 150"lbs. Then loosen the bolts and repeat the torque process. this helps seat the rod bearing especially on a new rod. Measure the bore with your dial bore gauge opposite the parting lines. If using plasti gauge you will have to install the rod on the crank and use in accordance the plasti gauge instructions.

The rod bore should measure 1.183 +/.0005". With plasti gauge you are looking for about .003" clearance. From .0025-.0035" clearance is acceptable. Anything outside that dimension please call 800-521-3560 for recommendation.

Once clearance is set apply oil to rod, crank, and wrist pin and install this time torque to 170"lbs.

Improperly torquing rod bolts is one of the most common causes of rod failure.

Refer to instructions shipped with all rods and the video below for more detailed instructions.

Reviews

Average Rating:
( 3 )
Amalia Correa from Hatillo, PA United States
August 10, 2024
Was this review helpful to you?
Isaac Brewbaker from Onaway, MI United States
April 14, 2021
Great
I had a great experience. Shipping was very fast and easy. When I call someone answered the phone and helped me. Great experience and service
Was this review helpful to you?
Matthew Brown from Tampa, FL United States
December 27, 2019
Billet rod
A must in any build and the best place to buy any part is studz. With lots of choices it's good to buy from a place that is always their to help
Was this review helpful to you?
Empty Cart